注册 登录  
 加关注
   显示下一条  |  关闭
温馨提示!由于新浪微博认证机制调整,您的新浪微博帐号绑定已过期,请重新绑定!立即重新绑定新浪微博》  |  关闭

gmd20的个人空间

// 编程和生活

 
 
 

日志

 
 

如何配置使用串口设备登录linux终端Linux Serial Console HOWTO  

2009-08-07 11:52:12|  分类: linux相关 |  标签: |举报 |字号 订阅

  下载LOFTER 我的照片书  |
原文地址:http://www.vanemery.com/Linux/Serial/serial-console.html
它附录的资源里面的几篇文章也是不错的

刚刚发现ubuntu的官方文档也差不多的:https://help.ubuntu.com/community/SerialConsoleHowto

Linux Serial Console HOWTO

by Van Emery


RS-232C Connectors

Introduction

Have you ever needed to connect a dumb terminal (like a Wyse 50) to a Linux host? Do you need to login to a Linux server from a laptop to perform administrative functions, because there is no monitor or keyboard attached to the server? If you are accustomed to administering routers, switches, or firewalls in this manner, then you may be interested in doing the same with some of your GNU/Linux hosts. This HOWTO will explain, step-by-step, how to setup a serial console for Red Hat 9, although most of it should apply to other distributions as well.

Why did I write this document? Although there are lots of documents available on the Internet dealing with Linux serial ports, most of them seemed to be either out of date, or focused on modem dial-in/dial-out. I wanted consise documentation on how to setup simple terminal access via RS-232-C serial ports for Red Hat 9.

Assumptions/Setup

I was using Red Hat 9 for this test. My test machine consisted of:

  • Motherboard: Gigabyte Technology GA-7VA motherboard (Rev. 2.0)
  • Chipset: VIA KT400A
  • CPU: AMD-K7 (Duron 1400)
  • RAM: 256MB DDR333
  • Serial Ports: 2 built-in ports with 16550A UARTs, DB-9 male
  • Linux kernel: 2.4.20-24.9

Step 1: Check your system's serial support

First, let's make sure that your operating system recognizes serial ports in your hardware. You should make a visual inspection and make sure that you have one or more serial ports on your motherboard or add-in PCI card. Most motherboards have two built-in ports, which are called COM1: and COM2: in the DOS/Windows world. You may need to enable them in BIOS before the OS can recognize them. After your system boots, you can check for serial ports with the following commands:

[root@oscar root]# dmesg | grep tty
ttyS0 at 0x03f8 (irq = 4) is a 16550A
ttyS1 at 0x02f8 (irq = 3) is a 16550A

[root@oscar root]# setserial -g /dev/ttyS[01]
/dev/ttyS0, UART: 16550A, Port: 0x03f8, IRQ: 4
/dev/ttyS1, UART: 16550A, Port: 0x02f8, IRQ: 3

As you can see, the two built-in serial ports are /dev/ttyS0 and /dev/ttyS1.


Step 2: Configure your inittab to support serial console logins

The /etc/inittab file must be reconfigured to allow serial console logins. You will note that the mingetty daemon is used to listen for virtual consoles (like the 6 that run by default with your keyboard and monitor). You will need to configure agetty or mgetty to listen on the serial ports, because they are capable of responding to input on physical serial ports. In the past, I have used both full-featured gettys. In this document, I will only discuss agetty, since it is already included in the default Red Hat 9 installation. It handles console/dumb terminal connections as well as dial-in modem connections.

What is a getty?

A getty is is a program that opens a tty port, prompts for a login name, and runs the /bin/login command. It is normally invoked by init.

Before you edit /etc/inittab, which is a very important config file, you should make a backup copy:

[root@oscar etc]# cp /etc/inittab /etc/inittab.org

The required /etc/inittab additions are highlighted in red:

id:3:initdefault:

# System initialization.
si::sysinit:/etc/rc.d/rc.sysinit

l0:0:wait:/etc/rc.d/rc 0
l1:1:wait:/etc/rc.d/rc 1
l2:2:wait:/etc/rc.d/rc 2
l3:3:wait:/etc/rc.d/rc 3
l4:4:wait:/etc/rc.d/rc 4
l5:5:wait:/etc/rc.d/rc 5
l6:6:wait:/etc/rc.d/rc 6

# Trap CTRL-ALT-DELETE
ca::ctrlaltdel:/sbin/shutdown -t3 -r now

pf::powerfail:/sbin/shutdown -f -h +2 "Power Failure; System Shutting Down"

# If power was restored before the shutdown kicked in, cancel it.
pr:12345:powerokwait:/sbin/shutdown -c "Power Restored; Shutdown Cancelled"

# Run gettys in standard runlevels
1:2345:respawn:/sbin/mingetty tty1
2:2345:respawn:/sbin/mingetty tty2
3:2345:respawn:/sbin/mingetty tty3
4:2345:respawn:/sbin/mingetty tty4
5:2345:respawn:/sbin/mingetty tty5
6:2345:respawn:/sbin/mingetty tty6

# Run agetty on COM1/ttyS0 and COM2/ttyS1
s0:2345:respawn:/sbin/agetty -L -f /etc/issueserial 9600 ttyS0 vt100
s1:2345:respawn:/sbin/agetty -L -f /etc/issueserial 38400 ttyS1 vt100
#s1:2345:respawn:/sbin/agetty -L -i 38400 ttyS1 vt100


# Run xdm in runlevel 5
x:5:respawn:/etc/X11/prefdm -nodaemon


agetty options explained:

  • -L    force line to be local line with no need for carrier detect (when you have no modem).
  • -f    alternative /etc/issue file. This is what a user sees at the login prompt.
  • -i    do not display any messages at the login prompt.
  • 9600    serial line rate in bps. Set this to your dumb terminal or terminal emulator line rate.
  • ttyS0    this is the serial port identifier.
  • vt100    is the terminal emulation. You can use others, but VT100 is the most common or "standard". Another widely used termial type is VT102.

Possible serial line rates (sometimes called baud rates) for the 16550A UART:

  • 110 bps
  • 300 bps
  • 1200 bps
  • 2400 bps
  • 4800 bps
  • 9600 bps
  • 19,200 bps
  • 38,400 bps
  • 57,600 bps
  • 115,200 bps

I have tried all of these line rates. 9600 bps is generally O.K., and is a very common setting for networking hardware. 38,400 bps is the speed of the standard Linux console, so it is my second choice. If your dumb terminal or terminal emulator cannot handle 38,400 bps, then try 19,200 bps: it is reasonably speedy and you will not be annoyed.

Here was my custom issue file, /etc/issueserial. It uses escape sequences defined in the agetty manpage to add some useful information, such as the serial port number, line speed, and how many users are currently logged on:


Oscar
Connected on \l at \b bps
\U

Now, you must activate the changes that you made in /etc/inittab. This is done with the following command, which forces the init process to re-read the configuration file:

[root@oscar root]# init q

Now, let's make sure that the agetty process is listening on the serial ports:

[root@oscar root]$ ps -ef | grep agetty
root 958 1 0 Dec13 ttyS0 00:00:00 /sbin/agetty -L -f /etc/issueserial 9600 ttyS0 vt100
root 1427 1 0 Dec13 ttyS1 00:00:00 /sbin/agetty -L -f /etc/issueserial 38400 ttyS1 vt100


Step 3: Test serial port login with an external dumb terminal or terminal emulator


Wyse 50b

I have tested this setup with a WYSE dumb terminal, a Linux laptop running Minicom, and Windows 2000/XP laptops running HyperTerminal. They all worked just fine.

Terminal settings:  should be 9600, N, 8, 1. Terminal emulation should be set to VT100 or VT102. Turn flow control off. If you want to use the 38,400 bps serial port on ttyS1, then your settings should be adjusted to 38400, N, 8, 1.

Cable:  To connect a laptop to the serial port on the Linux host, you need to have a null-modem cable. The purpose of a null-modem cable is to permit two RS-232 DTE devices to communicate with each other without modems between them. While you can construct this yourself, a good, sturdy manufactured null-modem cable is inexpensive and will last longer.

If you insist on making the cable yourself, then check out Nullmodem.Com for the wiring and pinout diagram.

Connectors:  Motherboard serial ports are typically male DB-9 connectors, but some serial ports use DB-25 connectors. You may need some DB-9 to DB-25 converters or gender-changers in order to connect to your terminal. For a typical laptop to server connection, a DB-9 null-modem cable should be sufficient.

Here is what you should see on the dumb terminal or terminal emulator:

Oscar
Connected on ttyS1 at 38400 bps
3 users

oscar.vanemery.com login:

Note:  If you want to be able to login via serial console as the root user, you will need to edit the /etc/securetty config file. The entries to add are highlighted in red:

console
ttyS0
ttyS1

vc/1
vc/2
vc/3
vc/4
vc/5
vc/6
vc/7
vc/8
vc/9
vc/10
vc/11
tty1
tty2
tty3
tty4
tty5
tty6
tty7
tty8
tty9
tty10
tty11


Step 4: Modifying the agetty settings

If you want to change the baud rate or some other agetty setting, you will need to perform these 3 steps:

  1. Modify the /etc/inittab configuration file
  2. Activate the config change by forcing init to re-read the config file
  3. Restart the agetty daemons

Here is an example of steps 2 and 3:

[root@oscar root]# init q
[root@oscar root]# pkill agetty


Optional:  Configure serial port as THE system console

You can use options in /etc/grub.conf to redirect console output to one of your serial ports. This can be handy if you do not have a keyboard or monitor available for the Linux host in question. You can also see all of the bootup and shutdown messages from your terminal. In this example, we will make the /dev/ttyS1 port be the console. The text to add to the config file is highlighted in red:

# grub.conf generated by anaconda
#boot=/dev/hda
default=0
timeout=10
splashimage=(hd0,0)/grub/splash.xpm.gz
title Red Hat Linux (2.4.20-24.9)
root (hd0,0)
kernel /vmlinuz-2.4.20-24.9 ro root=LABEL=/ console=ttyS1,38400
initrd /initrd-2.4.20-24.9.img

Now, if you drop your system into single user mode with the "init 1" command, you will still be able to administer the system from your serial-connected terminal. No monitor or keyboard is required!

Warning!:   The kudzu hardware detection program may "choke" on boot when the serial port becomes the console, instead of the video adapter. To remedy this situation, you should disable kudzu (assuming that your hardware is configured properly and won't be changing). This is how you would do that:

[root@oscar root]# chkconfig kudzu off
[root@oscar root]# chkconfig --list kudzu
kudzu 0:off 1:off 2:off 3:off 4:off 5:off 6:off

You should also know how to break into the Grub bootloader during system startup and edit the kernel line. By deleting the console argument from the kernel line, you can boot the system with the standard console, which uses the video card and attached keyboard. You have been warned!


Conclusion

Now, you should be able to login from the serial ports on your GNU/Linux host. This could be useful for maintenance or for serving a whole room full of dumb terminals. In the future, I will investigate a PCI multiport serial card in the latter role.

Have fun!



Resources

  评论这张
 
阅读(1266)| 评论(0)
推荐 转载

历史上的今天

评论

<#--最新日志,群博日志--> <#--推荐日志--> <#--引用记录--> <#--博主推荐--> <#--随机阅读--> <#--首页推荐--> <#--历史上的今天--> <#--被推荐日志--> <#--上一篇,下一篇--> <#-- 热度 --> <#-- 网易新闻广告 --> <#--右边模块结构--> <#--评论模块结构--> <#--引用模块结构--> <#--博主发起的投票-->
 
 
 
 
 
 
 
 
 
 
 
 
 
 

页脚

网易公司版权所有 ©1997-2017